Denso Liquid Coatings
For Technical Data Sheets, please click our Catalogue.
Protal is Denso’s line of protective pipeline coatings that can be applied by hand
or spray method. We offer a full range of fast cure, high build epoxies for a variety
of above and below ground corrosion protection. Our Protal Liquid coatings can easily
be applied in high and low temperature environments. Our coatings
are great for protecting girth welds, tie-ins, cadwells, fittings, fabrications,
repairs to FBE and rehabilitation to existing pipelines. Our pipeline coatings are
high build, up to 1270 micron in one coat.
Liquid Coatings Brochure
Specification Guides
Protal 7200 - High Build, Fast Cure Pipeline Coating
A fast cure, one coat epoxy coating that can be hand or spray applied to girth welds,
tie-ins, fittings and rehabilitation of existing pipelines. Exhibits excellent cathodic
disbondment properties at 80°C (175°F) with 7 mm disbondment.
Protal 7200 Repair Cartridge (400 ml) - Fast Cure Epoxy Repair Coating
Repair coating for damaged FBE and other liquid coated pipelines. Also used as coating
of cadweld areas.
Protal Air Cartridge Gun (1000 ml) - For Spraying Cartridges of Protal Liquid
Coatings
Can be used in a wide variety of spray applications using Protal Liquid Coatings.
It is designed for use where fast and easy setup, no clean up, minimal material
waste and minimal equipment maintenance is needed.
Protal 7200 Cartridge (1000 ml) - Fast Cure, High Build Spray Applied Pipeline
Coating
Protal 7200 Cartridge (1000 ml) is a VOC free, 100% solids, 2 part epoxy coating
specially formulated to compliment FBE coated pipe.
Protal 7300 - Moisture tolerant pipeline coating
Protal 7300 is a VOC free, 100% solids epoxy coating specially formulated to coat dry, damp or wet surfaces. It is a high build
epoxy coating that can be applied by applicator pad or brush.
Protal 7900HT - High Temperature Pipeline Coating
A high build epoxy coating that can be hand applied to girth welds, tie-ins, fittings
and rehabilitation of existing pipelines. Maximum operating temperature up to 150°C (302°F).
Protal 7900HT Cartridge (1000 ml) - High Temperature Spray Applied Pipeline Coating
Protal 7900HT Cartridge (1000 ml) is a VOC free, 100% solids, 2 part epoxy coating for pipelines operating at higher temperatures. It is a high build
liquid coating that is spray applied in one coat in the field or shop. It cures fast to allow quick backfill when applied to hot pipe.
Protal ARO - Abrasion Resistant Pipeline Coating
Protal ARO is a VOC free, 100% solids liquid epoxy coating formulated to be applied
over FBE as an ARO coating (abrasion resistant overlay). It is a 3:1 ratio compatible
for most plural component spray units coating that can be spray or hand applied
in the field or shop.
Denso ST Epoxy - Surface Tolerant Liquid Epoxy
A fast drying surface tolerant epoxy coating that can be hand or spray applied to
wire brushed rusty steel surfaces. Used for above and below ground pipelines, structural
steel, bridges, tanks, and other steel surfaces.
Denso Epoxy S™ - Fluid Epoxy Grout, High Strength, High Performance
Denso Epoxy S is a two component, high performance, pre filled epoxy grout, suitable
for use as a pourable or fluid grouting material. Fillers may be added to produce a
trowellable high build mortar or a pourable flowable grout.
Denso Archco 65 - High Solids Aliphatic Polyurethane
Used as a topcoat over Protal Liquid Coatings to provide color coding, abrasion
resistance, chemical resistance and UV stability. Will cure at temperatures as low
as 4°C (40°F).
Denso-Ramic - Epoxy Based System, Abrasive Resistant Additives
Is a tough, wear resistant, trowelable ceramic lining system for chutes, bins, pipe elbows, screen underpans, pumps etc. It is
applied as a coating offering good mechanical and chemical resistance.
Denso Covercoat/Basecoat Kit - Tough, Protective Outer Coating
Denso Covercoat/Basecoat Kit is a two component, hard wearing coating, consisting of a liquid portion containing synthetic
polymers, waterproofing admixtures and a cementitious powder portion consisting of fine fillers.
Single-Pack Elastomeric Membrane - Single Component, Moisture Curing
Being polyurethane based, it cures to form a tough, flexible, waterproofing and sealing membrane.
Denso Acrylic Topcoat - Integral Component in Various Denso Coating Systems
An acrylic paint designed for use in various applications. Pigmented, water-based, high opacity, acrylic paint. Available in white,
black, grey & mist green.
Denso Weatherseal Topcoat Acrylic - Two Component High Gloss Acrylic Based
Used as final topcoat for the Denso Steelcoat 700 corrosion protection system to help guard against ultraviolet radiation and
give a glossy durable finish in outdoor environments.
Denso S900 - Siloxane Waterproofing Solution
Denso S900 is a siloxane waterproofing solution which deeply penetrates into porous substrates to create a waterproofing
barrier below the surface.